This wiki has been migrated to and is now deprecated. Please use that site instead.
Differences between revisions 28 and 30 (spanning 2 versions)
Revision 28 as of 2008-06-12 16:04:31
Size: 5725
Editor: GuyHarris
Comment: Make "ipconfig /all" a step in the recipe.
Revision 30 as of 2008-07-10 21:22:18
Size: 5945
Editor: 64-128-15-244
Deletions are marked like this. Additions are marked like this.
Line 39: Line 39:
NOTE: To get to the Microsoft Loopback Adapter Properties: Start -> Settings -> Control Panel -> System -> Device Manager -> Network Adapters and right click Microsoft Loopback Adapter to select Properties.
-- saran

Loopback capture setup

The following will explain capturing on loopback interfaces a bit.

If you are trying to capture traffic from a machine to itself, that traffic will not be sent over a real network interface, even if it's being sent to an address on one of the machine's network adapters. This means that you will not see it if you are trying to capture on, for example, the interface device for the adapter to which the destination address is assigned. You will only see it if you capture on the "loopback interface", if there is such an interface and it is possible to capture on it; see the next section for information on the platforms on which you can capture on the "loopback interface".

Supported Platforms

See CaptureSetup/NetworkMedia for Wireshark capturing support on various platforms. Summary: you can capture on the loopback interface on Linux, on various BSDs including Mac OS X, and on Digital/Tru64 UNIX, and you might be able to do it on Irix and AIX, but you definitely cannot do so on Solaris, HP-UX, or Windows.



You can't capture on the local loopback address!

IP other

You can add a virtual network card called Microsoft Loopback Adapter, but in most cases that might not give results as expected either.

This adapter is available from Microsoft:

... and is quite different than the ones available for various UN*X systems. This adapter is a virtual network adapter you can add, but it will not work on the IP addresses; it will take its own IP address. BTW: You can only add one Loopback Adapter to the system!

/!\ Beware: Capturing from this Loopback Adapter requires the WinPcap 3.1 release, 3.1 beta versions won't work!

Let's suppose you have set the IP address of the loopback adapter to and are capturing on that interface. If you ping to this address the ping will get ping replies, but you won't see any of this traffic in Wireshark (much like the problem). If you ping on, you won't get ping replies as there is obviously no remote host, but you will see the corresponding ARP requests in Wireshark.

The only benefit I can see so far is if you use it with colinux (and probably other PC virtualization software) to capture the traffic between Windows and the virtual machine. - UlfLamping

:) Recipe (to capture traffic on ms loopback adapter / Windows XP): --- by mitra

1. go to MS Loopback adapter properties, set IP, MASK
2. ipconfig /all and look at the MAC-ID for your new adapter.
3. arp -s <MAC-ID>
4. route add mask
5. to test: "telnet"

{OK} I am now using the loopback adapter to capture traffic that I source into a Dyanmips/Dynagen virtual router network. This is a potentially very useful tool/feature that I will be testing further in the weeks to come. As it stands, I can connect my loopback adapter to a virtual router interface and capture ping, arp, etc. In the near future, I hope to tie a server w/ a loopback adapter to a virtual router and then capture a full client/server type of exchange across a Dynamips/Dynagen emulated network. -- Scott Vermillion

NOTE: To get to the Microsoft Loopback Adapter Properties: Start -> Settings -> Control Panel -> System -> Device Manager -> Network Adapters and right click Microsoft Loopback Adapter to select Properties. -- saran


A commercial network sniffer called CommView (from TamoSoft) allows to capture packets on the localhost network adapter but it dissects less protocols, so you can capture packets with CommView and save them into a file and open it with WireShark.

An other alternative is to add a route to your local machine going through the network gateway:

route add <your_IP> mask <the_gateway> metric 1

with <your_IP> being different from It should (has to) be the result of ipconfig command (ip address field) <the_gateway> has to be the default gateway field taken from ipconfig /all result.

Doing so, every network traffic from your machine to itself will use the physical network interface, it will then go to the gateway, back to you. Therefor, you will see each packet twice, but it can be filtered on the view.

Be careful, since your machine will use the actual network to talk to itself, it may overload the network. It may be wise to remove the new route once you are done with the tests:

route delete <your_IP>

This is translated from French, based on the method described here.

See Also

CaptureSetup/Loopback (last edited 2020-01-30 19:15:46 by ChristopherMaynard)